Plug-in transmitter High with display 0-10 V

Our High plug-in transmitter with display and 0-10 V voltage output comes with matching immersion sleeves (stainless steel immersion sleeve for aggressive media) and mounting flanges for quick and easy installation. The High plug-in transmitter with 0-10 V display measures the temperature in liquid or gaseous media, has eight switchable measuring ranges and a housing with a two-way display and IP 65.

Here you can find our downloads for Plug-in transmitter High with display 0-10 V

	Data sheet Plug-in transmitter High with display 0-10 V
	Instruction manual Plug-in transmitter High with display 0-10 V
	Declaration of Conformity Plug-in transmitter High with display 0-10 V

Plug-in transmitter with housing - Supply and output
Output					0 - 10 V
Power consumption					< 1,0 VA / 24 V DC; < 2,2 VA / 24 V AC
Voltage supply					24 V AC / DC (± 10 %)
Connection type					3-Wire
Plug-in transmitter with housing - General information
Measuring range					multi-range switching with 8 switchable measuring ranges with manual zero point correction (± 10 K)
Sensor					Pt1000 | Class B | DIN EN 60751
Temperature deviation					typically ± 0.2 K at +25 °C
Load resistance					Rl > 5 kOhm
Process connection					by using an immersion sleeve or mounting flange
Plug-in transmitter with housing - Ambient conditions
Ambient temperature					-30 °C to +70 °C
Permissible air humidity					< 95 % r. H., non-precipitating air
Plug-in transmitter with housing - Certifications / Standards
Protection class					III (nach EN 60 730)
Protection type					IP 65 according to EN 60 529
Standards					CE conformity electromagnetic compatibility according to EN 61326 according to EMC Directive 2014/ 30/ EU
Plug-in transmitter with housing - Technical drawing
Plug-in transmitter with housing - Protection sleeve
Material					Stainless steel 1.4571 | 316TI
Ø (mm)					6
Mounting length selectable (mm)					50, 100, 150, 200, 250, 300, 400
Other mounting lengths on request | tolerance ± 1 mm
Plug-in transmitter with housing - Gehäuse
Material					Plastic, UV-resistant Material polyamide, 30 % glass bead reinforced
Dimensions (L/W/H) (mm)					Aluminum die casting
Color					Traffic white (similar to RAL9016)
Electrical connection					0.14 - 1.5², via screw terminals on circuit board
Display					Two lines, lighted For display of actual temperature and self-diagnostics (overrange, underrange, probe break, probe short-circuit)
Cut-out Display (B/H) (mm)					ca. 36 x 15
Closure					with quick release screws
Cover					transparent
Screw connection					Cable gland, Plastic, M20x1,5, Strain relief, replaceable, max. 10,4 mm Ø Inner
Plug-in transmitter with housing - Important assembly instructions
					Measurement errors can occur due to heat dissipation to the environment. To keep these as small as possible, we recommend immersing the protective sleeve of your temperature sensor as deeply as possible in the medium to be measured when installing it. The optimum installation depth should be 10-15 times the Ø of the protective sleeve. Please make sure that you have enough space so that you can remove the sensor again if necessary.
Mounting by means of a mounting flange: Please ensure that the Ø of the mounting flange matches the Ø of the protective sleeve.
Mounting with immersion sleeve: Please make sure that the Ø and the length of the immersion sleeve match the installation situation so that the minimum immersion depth can be reached. Since the sensor is not inserted directly into the medium, but via the immersion sleeve, the response times are somewhat slower. The sensor should be selected so that the protective sleeve touches the bottom of the immersion sleeve and the air cushion around the protective tube is as small as possible. The use of thermal paste can improve the response times.
Plug-in transmitter with housing - Delivery & Packing
Delivery					Transmitter, Operating instructions
Packing					individually packed in PE bag