Kabel-Thermoelement Typ K mit PFA-Leitung

Vorschau: Kabel-Thermoelement Typ K mit PFA-Leitung Vorderansicht

Vorschau: Kabel-Thermoelement Typ K mit PFA-Leitung Technische Zeichnung

€ 12,43 *

zzgl. MwSt. zzgl. Versandkosten von 9,95 € nach AT (exkl. MwSt)

Lieferzeit 5 Werktage nach AT, NL, BE (DE -1 Werktag)

Wiederholte Bestellung: Einstellungen genau überprüfen und gegebenenfalls ändern.

1.Jetzt konfigurieren und bestellen

C - Länge Schutzhülse

D - Durchmesser Schutzhülse

E - Material Anschlussleitung

F - Länge Leitung

G - Stecker

H - Knickschutz

Image Changer

2.Wie viele Artikel benötigen Sie?

Menge

Preisberechnung

Grundpreis

€ 12,43

C - Länge Schutzhülse:
D - Durchmesser Schutzhülse:
E - Material Anschlussleitung:
F - Länge Leitung:
G - Stecker:
H - Knickschutz:
Menge:

Artikel-Nr.: 803570-1211

Unsere Zahlungsarten:

Ihre Vorteile bei Testo Sensor

Wir sind lieferfähig: Alle Infos hier
Beratung direkt durch Experten
Qualität direkt vom Hersteller
Langzeitstabile Temperaturfühler über Jahre
B2B-Kunden willkommen: Alle Infos hier

Fragen zum Artikel?
Unser Mitarbeiter hilft Ihnen gerne weiter:
Julian Mäntele
Tel.: +49 (0)7653 96 59 771
E-Mail: jmaentele@testo-sensor.de

Cable thermocouples with PFA cable are particularly versatile and can be used up to +260 °C.... mehr

Menü schließen

Produktinformationen "Kabel-Thermoelement Typ K mit PFA-Leitung"

Cable thermocouples with PFA cable are particularly versatile and can be used up to +260 °C. They are robust, acid-resistant, flexible and a good alternative to silicone cables.

Here you can find our downloads for the Cable thermocouple type K with PFA cable

	Data sheet Cable thermocouple type K with PFA cable
	Instruction manual Cable thermocouple type K with PFA cable
	Operating instruction Cable thermocouple Type K with PFA cable
	Declaration of Conformity Cable thermocouple type K with PFA cable

Cable thermocouple - General Information
Measuring range			-40 °C to +260 °C depending on chosen connection cable
Perm. °C range cable			-50 °C to +260 °C
Accuracy			-40 °C to +375 °C: ±1,5 °C according to DIN IEC 60584 Class 1
Response time			t63 / t99: information is available on request
Pull-out force			≥ 30 N

Cable thermocouple - Supply and output
Measuring element			Thermocouple Type K
Measuring point			Measuring point isolated
Measurement signal			Thermovoltage

Cable thermocouple - Ambient conditions
Protection class			IP65 according DIN 60529
Humidity and moisture condensation resistance			according to application-specific qualification

Cable thermocouple - Certificates and Standards
Standards			DIN EN 61326-1:2013 \| DIN EN IEC 63000:2019-05
Directive			RoHS 2011/65/EU \| 2014/30/EU
Certificates			Certificate of suitability (on request)

Cable thermocouple - Technical Drawing

						C - Length protection sleeve
						D - Diameter protection sleeve

						E - Material connection cable
						F - Length connection cable

						H - Bend protection

						G - Connector

						All dimensions in mm

Cable thermocouple - Protection sleeve
Diameter (mm)^1}			4, 5, 6
Length (mm)^2}			30, 40, 50, 60, 100, 200
^1} Tolerance ± 0,1 mm \| ^2} Tolerance length ≤ 100: ± 1 mm / length > 100: ± 1 %

Cable thermocouple - Material and possible configuration
Length / Ø (mm)	3		4		5		6
30	not available		Stainless steel 1.4404 \| 316L		Stainless steel 1.4404 \| 316L		Stainless steel 1.4404 \| 316L
40	not available		Stainless steel 1.4571 \| 316TI		Stainless steel 1.4404 \| 316L		Stainless steel 1.4404 \| 316L
50	not available		Stainless steel 1.4404 \| 316L		Stainless steel 1.4404 \| 316L		Stainless steel 1.4404 \| 316L
60	not available		not available		not available		Stainless steel 1.4571 \| 316TI
100	not available		Stainless steel 1.4571 \| 316TI		Stainless steel 1.4571 \| 316TI		Stainless steel 1.4571 \| 316TI
200	not available		Stainless steel 1.4571 \| 316TI		Stainless steel 1.4571 \| 316TI		Stainless steel 1.4571 \| 316TI
other protective sleeve lengths and Ø available on request

Cable thermocouple - Thermocouple cable
		Type	Color	Material (Outside / Inside)	Perm. range °C	Ø Outside (mm)		Cross section (mm²)	Color strand	Ω / m
		Thermocouple cable	Type K^1}	PFA / PFA	-50 to +260	2,5 ± 0,2		0,22	gn, wt	4,50^2}
Length (m)			1, 2, 3, 4, 5, 10, 15, 20
Insulation resistance: ≥ 100 MOhm at min. 100 VDC \| ^1}Color according to IEC 584 \| ^2}per thermocouple \| Cable available as accessory

Cable thermocouple - Connector
			Insulated end ferrules (50 mm)
			Mini-TC connector Type K gn
			Mini-TC connector Type K ye
			TC connector Type K gn
			TC connector Type K ye

Cable thermocouple - Delivery
Assembly instructions			by using compression fitting or immersion sleeve
Delivery and Packaging			Probe, seperatly packaged in PE bag
Matching accessories			Immersion sleeve, Heat-conducting paste, Compression fitting, Quick-release strap

Cable thermocouple - Important assembly advices
			Measurement errors can occur due to heat dissipation to the environment. To keep these as small as possible, we recommend immersing the protection sleeve of your temperature probe as deeply as possible in the medium to be measured during installation. The optimum installation depth should be 10-15 times the Ø of the protection sleeve or, when using an immersion sleeve, the Ø of the immersion sleeve. When installing in pipelines whose Ø does not have a sufficiently deep installation depth, you should install the probe either at an angle or in a pipe elbow. Make sure that there is sufficient space for the probe to be removed. 1) Installation with sufficient installation depth 2) Installation at an angle with small pipe Ø 3) Not like this: Minimum installation depth not reached
			Installation by means of compression fitting: Please tighten the union nut of the compression fitting by hand as far as it will go (clearly noticeable). For compression fittings with PTFE pressure ring, please make a 1/4 turn with a wrench suitable for the width across flats. These compression fittings can be used several times in this way. In the case of compression fittings with stainless steel cutting ring, the compression fitting connects to the protection tube. This connection is pressure resistant up to 40 bar. However, the compression fitting can only be used once. It must also be tightened more firmly. Please tighten it with 1 3/4 turns.
			Mounting by using an immersion sleeve (4): Please note that the Ø and the length of the immersion sleeve must be selected to suit the installation situation so that the minimum immersion depth can be achieved. Since the probe is not inserted directly into the medium, but via the immersion sleeve, the response times are somewhat slower. The probe should be selected in such a way that the protection sleeve touches the bottom of the immersion sleeve and that the air cushion around the protection sleeve is as small as possible. The use of thermal paste can improve the response times.
			Please lay the cable with reserve loop (4) and in such a way that no water can penetrate the sensor head. This allows you to extend the probe without disconnecting the electrical connection.

Qualification measurement series to ensure the function of our temperature probes over their service life
		Robust even with temperature changes	Temperature probes are exposed to harsh environmental conditions, such as changing temperatures and humidity, and should still work reliably in the field for 15 years or more.
		Resistant to heat and humidity	Extremely varying ambient conditions cause immense stress for the temperature probe and the design must be suitably robust and qualified.
		Long-term stable in any weather	Continuous exposure to sunlight, snow, fog, cold and ice shall not impair the function of the temperature probe and compliance with the specification.
		Robust even under high vibration load	Depending on the application, compressors and fans generate strong vibrations which are transmitted to components and cables. Therefore the used temperature probes have to be vibration resistant (20g).
		Reliable in practice: high pull-out force	The robust design ensures the necessary cable pull-out resistance, even under vibration and higher temperatures.
		Efficient through short response time	Depending on the application, short response times may be necessary to ensure efficient control of the system. Our sensor design is optimised for this requirement and we prove response times.
		Corrosion-resistant even in salt spray	Temperature probes are also used in coastal regions. For this reason, the temperature probes must also be able to withstand salty air for a lifespan of 15 years.
Applicable for this probe type

Eigenschaften

Thermoelement:	Typ K Klasse 1
Temperaturbereich:	-40 °C bis +260 °C
Leitungsmaterial:	PFA
Branche:	Automotive, Gebäudeautomation, Heizungstechnik, Klima- und Lüftungstechnik, Kunststoffindustrie, Kältetechnik, Lebensmittelindustrie, Maschinen- und Apparatebau, Pharmaindustrie, Weiße Ware

Weiterführende Links zu "Kabel-Thermoelement Typ K mit PFA-Leitung"

Verfügbare Downloads:

Bewertungen lesen, schreiben und diskutieren... mehr

Menü schließen

Kundenbewertungen für "Kabel-Thermoelement Typ K mit PFA-Leitung"

Bewertung schreiben

Jede Verbraucherbewertung wird vor ihrer Veröffentlichung auf ihre Echtheit überprüft, sodass sichergestellt ist, dass Bewertungen nur von Verbrauchern stammen, die die bewerteten Produkte auch tatsächlich erworben/genutzt haben. Die Überprüfung geschieht durch manuelle Überprüfung in Form eines Abgleichs der Bewertung mit der Bestellhistorie des Warenwirtschaftssystems, um einen vorangegangenen Produkterwerb zur notwendigen Bedingung für die Veröffentlichung zu machen.